Product Overview
The Bently Nevada 330130-040-00-05 3300 XL Standard Extension Cable provides a reliable, rugged link between 3300 XL proximity probes and transducer electronics. It solves field routing and distance limitations by offering a factory-configured, armored cable assembly that preserves signal integrity in harsh plant environments—reducing downtime and simplifying installation for condition‑monitoring systems.
Technical Specifications
Model Number: 330130-040-00-05
Product Series: Bently Nevada 3300 XL
Module Type: 3300 XL Standard Extension Cable (proximity/transducer extension)
Optimal Length: 4.0 meters (040 = 4.0 m)
Weight: 0.20 kg
Packaged Dimensions: 20.5 × 22.4 × 3.3 cm
Construction: Armored outer jacket for mechanical protection; factory‑terminated to match 3300 XL connectors/terminations
Conductor / Shielding: Manufacturer‑specified conductors with full shielding to minimise EMI (confirm conductor count/AWG in official datasheet)
Environmental Rating: Designed for industrial use; consult datasheet for exact temperature, ingress and chemical resistance ratings
System Compatibility: Designed for Bently Nevada 3300 / 3300 XL TSI systems and standard proximitor/transducer interfaces
Communication Support: Integrates within systems using Ethernet-based diagnostics/gateways as applicable
HS Code: 8537101190
Product Origin: USA
Lead Time: In stock — available for prompt shipment
Model Code Breakdown
330130 — Base part number identifying the extension-cable family for 3300/3300 XL systems.
-040 — Length code: 040 denotes 4.0 meters cable length.
-00 — Configuration/material placeholder: typically indicates standard factory construction/finish (no special mechanical options).
-05 — Termination/connector code: denotes the factory termination style or mating interface compatible with 3300 XL probes/monitors.
Note: Suffix meanings can vary by factory option tables; always confirm exact feature mappings (connector type, conductor count, jacket material) with the official Bently Nevada parts table or the supplier’s datasheet before ordering.
Installation Recommendations & Wiring Guide
Pre‑installation checks: Verify the cable part number matches required length and termination. Inspect connectors for damage and confirm mating compatibility with probe and monitor.
Routing & protection: Route extension cables in dedicated trays or conduits; maintain separation from high‑power and VFD wiring to reduce EMI. Use armored sections or conduit at cable entry points and through high-risk zones.
Connector mating: Align and engage factory connectors per Bently’s torque/engagement instructions. Use appropriate O‑rings or seals where required to maintain ingress protection.
Shielding & grounding: Maintain cable shield continuity to the monitoring end only (single‑point ground) unless system documentation specifies otherwise. Avoid ground loops by following plant grounding practices.
Strain relief & sealing: Provide proper strain relief at both terminations and use cable glands to maintain enclosure integrity and prevent moisture ingress.
Mechanical support: Support the cable at regular intervals to prevent undue stress on connectors; avoid sharp bends near terminations.
Commissioning: Verify continuity, insulation resistance, and connector pinouts before powering. After connection, perform a system check with the 3300/3300 XL monitor: confirm probe bias/expected signal and capture baseline readings for trend comparison.
Maintenance: Inspect cable armor and terminations periodically; replace if armor is breached or terminations show corrosion. Keep spare, factory‑terminated assemblies available for rapid replacement.
FAQ — Common Questions
Q: What is the purpose of the 330130-040-00-05 cable?
A: It is a factory‑terminated extension cable for 3300/3300 XL proximity probes, providing a rugged 4.0 m link between probes and monitor electronics.
Q: Is this a genuine Bently Nevada part?
A: Yes — this listing refers to the factory part 330130-040-00-05 designed for Bently 3300/3300 XL systems. Units are in stock and ready for fast shipment.
Q: Will this cable mate with my 3300 XL probe and monitor?
A: The -05 termination is intended for standard 3300 XL interfaces. Always verify connector type and pinout with your probe/monitor datasheet prior to installation.
Q: Can the cable be routed near power or VFD cables?
A: Avoid running parallel to high‑power/VFD cabling. Where unavoidable, cross at right angles and use additional shielding or conduit to mitigate EMI.
Q: What environments is the cable suitable for?
A: The armored construction is intended for harsh industrial environments; consult the official datasheet for exact temperature range, chemical and ingress ratings.
Q: Can I order custom lengths or different terminations?
A: Custom lengths and termination options are commonly available; contact sales with required length and connector specification for a quote and lead time.
Q: What commissioning checks should I perform after installation?
A: Verify continuity and insulation resistance, confirm correct pinout/connector mating, power up the 3300 monitor, check probe bias and zero offsets, then capture baseline vibration/position readings during run‑up.
For exact conductor sizes, pinouts, environmental ratings and any site‑specific requirements, please consult the official Bently Nevada datasheet or contact technical support prior to procurement and installation.
